Request A Quote
Features
| Features | Benefits |
| Surpassed rugged industry standards |
All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures. |
| Factory assembled | Saves customer set-up time and money. |
| 160 HP Divider gearbox and 75 HP wing gearboxes |
A rugged heavy built gearboxes capable of handling heavy cutting applications. |
| Gearbox Seal Protection | Gearbox bottom seal protection for longer bearing life. |
| Input driveline: Cat. 4 CV | Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline. |
| Easy greasable drivelines | Drivelines have access holes for greasing the U-joints and to grease the inner profiles. |
| 2 Plate slip-clutch | Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered. |
| 15,000 FPM High blade tip speed | Allows clean cutting of material and even distribution. |
| 6" Blade overlap | Eliminates skipping during turns. |
| 11 1/4" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
| 3/16" Gauge Stump jumper backed with a 1" thick mounting bar |
Allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal. |
| 10 Gauge smooth deck top | Reduces accumulation of debris and is easier and faster to clean. |
| 1/4" Plate side skirt | Reduces debris piercing possibilities. |
| Low hitch weight | Less drawbar wear. Less ballast required. Works well with lighter tractors. |
| Dual remote hydraulics | Easy to operate. Fits most tractors, only two duplex outlets required to lift wings and change cutting height separately. |
| Hinged wing sections | Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows can cause uneven cutting. Wings will hinge 20o down. |
| 7/8" Solid hinge rods | Gives great strength to the cutter from front to rear, and in the hinge area itself. |
| Wing transport locks | Holds transport wings in the folded-up position in case of hydraulic pressure loss. |
| Enclosed front to rear dual leveling rods |
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod. |
| 5-Bolt hubs | 5-Bolt hubs makes the wheel assembly more durable and longer lasting. |
| Drain holes in wheel rims | Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims. |
| Spring-cushioned lift cylinder | Cushions loads on drawbar. |
| Replaceable wheel spindles | Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove two bolts to replace damaged spindle. |
| 7/8" Leveling rods | Large diameter leveling rods provide superior supporting strength over rough terrain. |
| Airplane tires | Gives better cushion while transporting and provides flotation in soft ground. |
Specifications
| Specifications & Capacities | RC2515 |
| Tractor horsepower | 50-100 hp |
| Gearbox horsepower Splitter Center & wings |
160 hp 100 hp |
| Gearbox shafts input shaft output shaft |
1 3/8" 6 Spline 1 5/8" |
| Gearbox capacity & lubrication splitter center & wings |
4.5 Pints of gear lube 80-90W EP 5.75 Lints of gear lube 80-90W EP |
| Cutting capacity | 1 1/2" |
| Hitch weight | 1,022 lbs. |
| Machine weight | 3,202 lbs. with chain guards & four laminated tires. |
| Blade tip speed at 540 rpm | Center blades & wing blades = 14,963 FPM |
| Hitch types | Pull-type hitch & clevis |
| Hitch jack | Standard (2,000 lbs.) |
| Cutting width Overall width Normal transport width Minimum transport width |
15' - 0" 15' - 7" 10' - 2 1/2" With transport locks set and cutting blade 13" off the ground. 8' - 4" With transport locks set and cutting blade 2" off the ground. |
| Overall length | 15' - 2" With laminated tires 15' - 5 1/2" With aircraft tires |
| Deck height | 11 1/4" |
| Cutting height | 2" to 13" |
| Lift hydraulics | 2 1/2" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers |
| Wing hydraulics | 2 1/2" x 10" hydraulic cylinders, hoses & fittings |
| Wing transport protection | Wing transport locks |
| Deck material | 10 Gauge deck |
| Side skirt material | 1/4" Plate |
| Skid shoes | Wing Deck: 1 replaceable shoe per wing Center Deck: 2 replaceable shoes |
| Blade rotation left wing center deck right wing |
Clockwise Counterclockwise Counterclockwise |
| Blades - 6 (2 per deck) | 1/2" x 4" Heat treated free swinging alloy steel with up lift |
| Blade overlap | 6" |
| Blade bolt | Keyed with hardened flat washer & locknut |
| Stump jumper / blade holder | 10 Gauge round dish shaped pan, reinforced with 1" x 4" blade bar |
| Front & rear guards | Single chain or rubber |
| Input driveline | ASAE Category 4 with constant velocity u-joint |
| Intermediate & wing drivelines | ASAE Category 3 with slip-clutch |
| Wheels | 29" Used aircraft tires or 21" laminated wheels |
| Number of wheels | 4 or 6 Total |
| Transport axle | Spring-cushioned lift cylinder |
| Hubs | Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts |
| Colors | Standard color: Beige; Optional colors: Green, Orange, or Red |
Farm & Ranch Supplies
Our hardware department offers a wide selection of STIHL Power Equipment, fencing, irrigation supplies, and quality power and hand tools. We also have a full-service tack shop and western clothing department. So as you can see we are your one-stop-shop for all of your farming, ranching, and residential needs. Plus, we service all of the equipment we sell in our small engine repair shop. Our mechanics hold several certifications including STIHL silver or gold, Honda, Kohler, Briggs and ExMark.